How To Install Truconnex Ground Loop Isolator
5/24/2019
53 - Comments
How To Install Truconnex Ground Loop Isolator Rating: 3,7/5 1026 votes
It is a passive device and does not require any power. Telugu happy birthday song mp3 download. If you have multiple cameras with ground loop problems, you will need one isolator for each camera. Ground loop issues can be caused by different ground potentials between points, for example, between the camera and DVR. Alright I bought a ground loop isolator and attempted installing it. Unfortunately i cant install it. Reasons: The isolator has 2 male ends. RCA cable has 2 male ends.
2454Likes
| Thread Tools |
AVS Forum Addicted Member
Location: Orlando, FL (Scotland until May 22)
Mentioned: 676 Post(s)
Quoted: 21643 Post(s)
Originally Posted by Luisfc1972
subwoofer distance is 0.3ft from mlp?
front and left are 12ft, sub is next to the right front.
what happened? i really dont want to run audyssey again
Obviously a hiccup and yes, you will have to run Audyssey again although first lower the sub gain/volume knob to about 9 o'clock. Are the FL/FR speakers actually 12' from the 1st mic position? Normally the subwoofer 'distance' should be about 1.5x the actual distance as this number pertains to a 'delay' setting accounting for the filters used in the subwoofer rather than the actual distance the sub is from the 1st mic position.front and left are 12ft, sub is next to the right front.
what happened? i really dont want to run audyssey again
2018 Denon AVR Owner's thread
2018 Marantz AVR Owner's thread
2018 Marantz AVR Owner's thread
| Sponsored Links | |
Location: los angeles, california
Mentioned: 1 Post(s)
Quoted: 290 Post(s)
Originally Posted by jdsmoothie
Obviously a hiccup and yes, you will have to run Audyssey again although first lower the sub gain/volume knob to about 9 o'clock. Are the FL/FR speakers actually 12' from the 1st mic position? Normally the subwoofer 'distance' should be about 1.5x the actual distance as this number pertains to a 'delay' setting accounting for the filters used in the subwoofer rather than the actual distance the sub is from the 1st mic position.
the fl/fr speakers are around 12 from 1st mic position yes. everything sounds fine thoughMember
Posts: 48
Tagged: 0 Thread(s)
Liked: 10
I know I'm not going to phrase this quite right, and I apologize in advance for that. I have a 2112CI and have been thinking about getting a DAC for some time. The Oppo Sonica DAC has come out, and I'm intrigued by it. I am wondering though, if I send the output of the DAC through RCA into the CD input of the 2112, are there settings in the 2112 that will keep it from re-digitizing the sound and making the DAC a moot point? I'd poked around some and didn't find anything online that made me feel like I was finding an answer to this question.
| Sponsored Links | |
AVS Forum Special Member
Location: Borneo Island
Mentioned: 5 Post(s)
Quoted: 1308 Post(s)
Originally Posted by JohnJ9
I know I'm not going to phrase this quite right, and I apologize in advance for that. I have a 2112CI and have been thinking about getting a DAC for some time. The Oppo Sonica DAC has come out, and I'm intrigued by it. I am wondering though, if I send the output of the DAC through RCA into the CD input of the 2112, are there settings in the 2112 that will keep it from re-digitizing the sound and making the DAC a moot point? I'd poked around some and didn't find anything online that made me feel like I was finding an answer to this question.
Pure DIRECT mode AVS Forum Addicted Member
Location: Orlando, FL (Scotland until May 22)
Mentioned: 676 Post(s)
Quoted: 21643 Post(s)
Originally Posted by JohnJ9
I know I'm not going to phrase this quite right, and I apologize in advance for that. I have a 2112CI and have been thinking about getting a DAC for some time. The Oppo Sonica DAC has come out, and I'm intrigued by it. I am wondering though, if I send the output of the DAC through RCA into the CD input of the 2112, are there settings in the 2112 that will keep it from re-digitizing the sound and making the DAC a moot point? I'd poked around some and didn't find anything online that made me feel like I was finding an answer to this question.
Please post back with your impressions should you choose to purchase the Oppo DAC. 2018 Denon AVR Owner's thread
2018 Marantz AVR Owner's thread
2018 Marantz AVR Owner's thread
Member
Posts: 48
Tagged: 0 Thread(s)
Liked: 10
Originally Posted by Skylinestar
The things we forget..I decided to play with this today, turned on my CD player, and rounded up a few CDs, reminded myself how to use them (funny what atrophies over time, isn't it?), and played with the Pure Direct settings. I feel like I forgot what things sound like! The one thing I'm uncertain of is if I've still mucked things up. With the proper setting in hand, I poked through BatPig's cheat sheet, and I wanted to keep the 2.1 sound, so I set things to LFE+Main.
Even in a lossless format, I kind of feel like I'd just grown accustomed to what processed sound is like. There is a presence and aliveness in the sound today that I'd just forgotten. Digital storage means not having to buy two extra rooms to house the CDs, but today feels like a rediscovery. Am I still fooling myself by turning the LFE+Main on to force 2.1 sound? Will there be a similar awakening if I pick up the Oppo DAC and run my lossless through it without having to rummage for CDs? Does this really mean I don't need to go pop for a second amp and speakers to make the Oppo perform to its full capabilities? I've enjoyed my 2112, and I was wondering if the analog route really was still valid through the box.
BTW, in Pure Direct mode, once everything is set, the display goes blank. Alter the volume and it displays the change, then goes blank. Change to anything else that is not using Pure Direct and it all comes back. Is this normal?
AVS Forum Special Member
Location: Borneo Island
Mentioned: 5 Post(s)
Quoted: 1308 Post(s)
Originally Posted by JohnJ9
BTW, in Pure Direct mode, once everything is set, the display goes blank. Alter the volume and it displays the change, then goes blank. Change to anything else that is not using Pure Direct and it all comes back. Is this normal?
Yes, it is normal. Pure direct mode will switch off unnecessary stuffs for cleaner sound. Member
Posts: 28
Tagged: 0 Thread(s)
Liked: 3
Does anyone know a good place to buy rack ears for this model?
AVS Forum Addicted Member
Location: Orlando, FL (Scotland until May 22)
Mentioned: 676 Post(s)
Quoted: 21643 Post(s)
Originally Posted by DubDriver17
Does anyone know a good place to buy rack ears for this model?
Which model? There are 7 discussed in this thread. You can purchase directly from Denon parts department. 2018 Denon AVR Owner's thread
2018 Marantz AVR Owner's thread
2018 Marantz AVR Owner's thread
Member
Posts: 28
Tagged: 0 Thread(s)
Liked: 3
Originally Posted by jdsmoothie
Which model? There are 7 discussed in this thread. You can purchase directly from Denon parts department.
Sorry, I have the Denon 2112CI and would need the RM-R3312 kit, just can't seem to find it.AVS Forum Addicted Member
Ground Loop Isolator Car Audio
Location: Orlando, FL (Scotland until May 22)
Mentioned: 676 Post(s)
Quoted: 21643 Post(s)
Originally Posted by DubDriver17
Sorry, I have the Denon 2112CI and would need the RM-R3312 kit, just can't seem to find it.
Then likely no longer stocked by Denon. Maybe try eBay. 2018 Denon AVR Owner's thread
2018 Marantz AVR Owner's thread
2018 Marantz AVR Owner's thread
Member
Posts: 28
Tagged: 0 Thread(s)
Liked: 3
Originally Posted by jdsmoothie
Then likely no longer stocked by Denon. Maybe try eBay.
Yea thats what I was afraid of. Its blocked here at work so I'll look when I get home. Thanks anyway.
Newbie
Posts: 11
Tagged: 0 Thread(s)
Liked: 12
Might be a very newbie question but appreciate some input.
I'm upgrading my TV setup from FullHD to 4K+HDR and was wondering if my Denon 1912 is able to pull this off. Currently all my external devices (laptop, ps4pro, apple tv etc.) connect via HDMI cables to the 1912 and from 1912 I have a single HDMI going to my 1080p TV. Are there any limitations to using the same setup with 4K? Or is video a separate topic from the audio in this case and shouldnt matter?
Thanks!
I'm upgrading my TV setup from FullHD to 4K+HDR and was wondering if my Denon 1912 is able to pull this off. Currently all my external devices (laptop, ps4pro, apple tv etc.) connect via HDMI cables to the 1912 and from 1912 I have a single HDMI going to my 1080p TV. Are there any limitations to using the same setup with 4K? Or is video a separate topic from the audio in this case and shouldnt matter?
Thanks!
Advanced Member
Posts: 615
Tagged: 0 Thread(s)
Liked: 13
https://www.cnet.com/news/do-you-nee..ables-for-hdr/
'Every step in your AV chain (the expensive devices into which you plug the cables) generally must be HDMI 2.0a for HDR to work. As in, your TV, receiver and source all have to be HDMI 2.0a, and usually require HDCP 2.2 copy protection too. If your TV is HDR, it almost certainly has at least one HDMI input with 2.0a/2.2.'
Denon XX12 vintage does not have HDMI 2.0a. Get a newer receiver.
'Every step in your AV chain (the expensive devices into which you plug the cables) generally must be HDMI 2.0a for HDR to work. As in, your TV, receiver and source all have to be HDMI 2.0a, and usually require HDCP 2.2 copy protection too. If your TV is HDR, it almost certainly has at least one HDMI input with 2.0a/2.2.'
Denon XX12 vintage does not have HDMI 2.0a. Get a newer receiver.
AVS Forum Addicted Member
Location: Orlando, FL (Scotland until May 22)
Mentioned: 676 Post(s)
Quoted: 21643 Post(s)
Originally Posted by pfft!!
Might be a very newbie question but appreciate some input.
I'm upgrading my TV setup from FullHD to 4K+HDR and was wondering if my Denon 1912 is able to pull this off. Currently all my external devices (laptop, ps4pro, apple tv etc.) connect via HDMI cables to the 1912 and from 1912 I have a single HDMI going to my 1080p TV. Are there any limitations to using the same setup with 4K? Or is video a separate topic from the audio in this case and shouldnt matter?
Thanks!
The 1912 was released in 2011 and is only HDMI 1.4a. To be 4k/HDCP 2.2/HDR compliant, you must purchase a 2015 or newer AVR that is at least HDMI 2.0a as well as using the newer 'Premium' certified 4k/18gbps HDMI cables.I'm upgrading my TV setup from FullHD to 4K+HDR and was wondering if my Denon 1912 is able to pull this off. Currently all my external devices (laptop, ps4pro, apple tv etc.) connect via HDMI cables to the 1912 and from 1912 I have a single HDMI going to my 1080p TV. Are there any limitations to using the same setup with 4K? Or is video a separate topic from the audio in this case and shouldnt matter?
Thanks!
https://www.monoprice.com/product?c_..seq=1&format=2
2018 Denon AVR Owner's thread
2018 Marantz AVR Owner's thread
2018 Marantz AVR Owner's thread
Member
Posts: 46
Tagged: 0 Thread(s)
Liked: 11
Batpig wrote in the OP:
'In Standby they will use 0.1W with HDMI Control OFF and about 2.2W with HDMI Control or Network Standby/IP Control set to ON.'
Has the 2312 standby power consumption been measured with HDMI Control on? The 2310 was reported as drawing ~30W in standby with HDMI Control on.
What changed to reduce the 2312 standby consumption with HDMI Control on so significantly?
'In Standby they will use 0.1W with HDMI Control OFF and about 2.2W with HDMI Control or Network Standby/IP Control set to ON.'
Has the 2312 standby power consumption been measured with HDMI Control on? The 2310 was reported as drawing ~30W in standby with HDMI Control on.
What changed to reduce the 2312 standby consumption with HDMI Control on so significantly?
AVS Forum Addicted Member
Location: Orlando, FL (Scotland until May 22)
Mentioned: 676 Post(s)
Quoted: 21643 Post(s)
Originally Posted by Sithuk
Batpig wrote in the OP:
'In Standby they will use 0.1W with HDMI Control OFF and about 2.2W with HDMI Control or Network Standby/IP Control set to ON.'
Has the 2312 standby power consumption been measured with HDMI Control on? The 2310 was reported as drawing ~30W in standby with HDMI Control on.
What changed to reduce the 2312 standby consumption with HDMI Control on so significantly?
Yup. From p. 145 of the Owner's manual ..'In Standby they will use 0.1W with HDMI Control OFF and about 2.2W with HDMI Control or Network Standby/IP Control set to ON.'
Has the 2312 standby power consumption been measured with HDMI Control on? The 2310 was reported as drawing ~30W in standby with HDMI Control on.
What changed to reduce the 2312 standby consumption with HDMI Control on so significantly?
2018 Denon AVR Owner's thread
2018 Marantz AVR Owner's thread
2018 Marantz AVR Owner's thread
Member
Posts: 88
Tagged: 0 Thread(s)
Liked: 4
I have a Denon AVR-1612 connected to my PC's 3.5mm audio out jack for sometime. Lately I've noticed a very loud buzzing when the PC audio out is connected to the Denon's V.Aux audio in from the front panel.
Once I was able to move the cable and the buzzing disappeared until I moved and reconnected the audio cable again. This happened only once and moving the audio cable currently has no effect on the buzzing sound.
Th 3.5mm stereo audio cable from the PC audio out is connected to a 3.5mm to RCA stereo Y spitter that's connected to the Denon V.Aux in on the front panel.
After going into the AVR-1612 setup and playing around with various settings and adjustments including cross-over frequency, etc. The buzzing has subsided somewhat when the AVR's volume is around -10 - 12 db however it's starts to become significant at around -8 db, higher volumes the buzzing starts to become bad again.
I'm planning on purchasing a Ground Loop Isolator such as a Boss B25N. Also perhaps getting another audio cable and installing some ferrite cord noise suppressors on both ends of the audio cable.
I'm wondering what else I can do to test and eliminate the buzzing noise? Try other connectors and cables?
I'm unable to isolate the interference that's causing the buzzing. I've tried moving around and reconnecting the speakers and cables. Moving the PC to AVR audio cable, moving around any other cables near the PC, AVR and speakers.
Once I was able to move the cable and the buzzing disappeared until I moved and reconnected the audio cable again. This happened only once and moving the audio cable currently has no effect on the buzzing sound.
Th 3.5mm stereo audio cable from the PC audio out is connected to a 3.5mm to RCA stereo Y spitter that's connected to the Denon V.Aux in on the front panel.
After going into the AVR-1612 setup and playing around with various settings and adjustments including cross-over frequency, etc. The buzzing has subsided somewhat when the AVR's volume is around -10 - 12 db however it's starts to become significant at around -8 db, higher volumes the buzzing starts to become bad again.
I'm planning on purchasing a Ground Loop Isolator such as a Boss B25N. Also perhaps getting another audio cable and installing some ferrite cord noise suppressors on both ends of the audio cable.
I'm wondering what else I can do to test and eliminate the buzzing noise? Try other connectors and cables?
I'm unable to isolate the interference that's causing the buzzing. I've tried moving around and reconnecting the speakers and cables. Moving the PC to AVR audio cable, moving around any other cables near the PC, AVR and speakers.
AVS Forum Addicted Member
Location: Orlando, FL (Scotland until May 22)
Mentioned: 676 Post(s)
Quoted: 21643 Post(s)
Originally Posted by Neb Ula
I have a Denon AVR-1612 connected to my PC's 3.5mm audio out jack for sometime. Lately I've noticed a very loud buzzing when the PC audio out is connected to the Denon's V.Aux audio in from the front panel.
Once I was able to move the cable and the buzzing disappeared until I moved and reconnected the audio cable again. This happened only once and moving the audio cable currently has no effect on the buzzing sound.
Th 3.5mm stereo audio cable from the PC audio out is connected to a 3.5mm to RCA stereo Y spitter that's connected to the Denon V.Aux in on the front panel.
After going into the AVR-1612 setup and playing around with various settings and adjustments including cross-over frequency, etc. The buzzing has subsided somewhat when the AVR's volume is around -10 - 12 db however it's starts to become significant at around -8 db, higher volumes the buzzing starts to become bad again.
I'm planning on purchasing a Ground Loop Isolator such as a Boss B25N. Also perhaps getting another audio cable and installing some ferrite cord noise suppressors on both ends of the audio cable.
I'm wondering what else I can do to test and eliminate the buzzing noise? Try other connectors and cables?
I'm unable to isolate the interference that's causing the buzzing. I've tried moving around and reconnecting the speakers and cables. Moving the PC to AVR audio cable, moving around any other cables near the PC, AVR and speakers.
Start with the troubleshooting steps you have already listed. Once I was able to move the cable and the buzzing disappeared until I moved and reconnected the audio cable again. This happened only once and moving the audio cable currently has no effect on the buzzing sound.
Th 3.5mm stereo audio cable from the PC audio out is connected to a 3.5mm to RCA stereo Y spitter that's connected to the Denon V.Aux in on the front panel.
After going into the AVR-1612 setup and playing around with various settings and adjustments including cross-over frequency, etc. The buzzing has subsided somewhat when the AVR's volume is around -10 - 12 db however it's starts to become significant at around -8 db, higher volumes the buzzing starts to become bad again.
I'm planning on purchasing a Ground Loop Isolator such as a Boss B25N. Also perhaps getting another audio cable and installing some ferrite cord noise suppressors on both ends of the audio cable.
I'm wondering what else I can do to test and eliminate the buzzing noise? Try other connectors and cables?
I'm unable to isolate the interference that's causing the buzzing. I've tried moving around and reconnecting the speakers and cables. Moving the PC to AVR audio cable, moving around any other cables near the PC, AVR and speakers.
2018 Denon AVR Owner's thread
2018 Marantz AVR Owner's thread
2018 Marantz AVR Owner's thread
Member
Posts: 88
Tagged: 0 Thread(s)
Liked: 4
Originally Posted by jdsmoothie
Start with the troubleshooting steps you have already listed.
I've found several ground loop isolators. Anyone have any suggestions?Some appear to also have noise suppression filters?
25 AMP Hi-low Converter Ground Loop Isolator AD-205A
Truconnex 2 Series Ground Loop Isolator TC-GLI
Raptor GL15 Gold Series
L.O.C.PRO LPGL-2 Universal Ground Loop Isolator
Absolute HLA600 2 Channel High Level to Low Converter Line Output with Ground Loop Isolator Built in signal Noise Eliminator
BOSS Audio B25N
Last edited by Neb Ula; 03-30-2017 at 09:06 AM.
AVS Forum Special Member
Location: MD
Mentioned: 10 Post(s)
Quoted: 752 Post(s)
Samsung 4K 65' HU8550/3500/JS9000 Mod(M68), Denon AVR-X4200, ATMOS/DTSX 7.3.2, Cerwin Vega x7, DefTech Sub x3, Micca R-8C 8' Ref Series x2
TiVo Roamio OTA 3TB Lifetime, 3x TiVo Mini's, TiVo Stream, HD Homerun Extend
Winegard HD7697 Roof Antenna, Nvidia Sheild
HTPC: AMD FX8350, GSkill TridentX 16GB CL8, LG WH16NS40 BD-RW, EVGA GTX-1080, GTX-1070, (3) 27' 2ndary Monitors
TiVo Roamio OTA 3TB Lifetime, 3x TiVo Mini's, TiVo Stream, HD Homerun Extend
Winegard HD7697 Roof Antenna, Nvidia Sheild
HTPC: AMD FX8350, GSkill TridentX 16GB CL8, LG WH16NS40 BD-RW, EVGA GTX-1080, GTX-1070, (3) 27' 2ndary Monitors
Member
Posts: 88
Tagged: 0 Thread(s)
Liked: 4
Originally Posted by doctorwizz
Uncertain if it would make any difference ..I have some older heavy duty insulated RCA stereo audio cables, leftovers from my old school audio equipment, used with a Teac SX series reel to reel tape deck
PC > (3.5mm male to 2 x RCA female stereo Y adapter) >
> (Better insulated L/R stereo RCA cord) >
> (RCA stereo ground isolator) > AVR RCA stereo audio aux. input
Instead of using a thinner 3.5mm audio cord (with 3.5mm male connectors) having less insulation.
Current install: PC => (3.5mm male = thinner stereo audio cord = 3.5mm male) => 3.5mm to RCA Y adapter > AVR rca stereo aux. input.
Member
Posts: 88
Tagged: 0 Thread(s)
Liked: 4
Ok thanks for the suggestion.
Ordered the Boss BN25 and found a better 3.5mm cable and a Y adapter on MonoPrice.com.
Ordered the Boss BN25 and found a better 3.5mm cable and a Y adapter on MonoPrice.com.
AVS Forum Special Member
Location: Borneo Island
Mentioned: 5 Post(s)
Quoted: 1308 Post(s)
Currently I don't have any speakers attached to my 3312. Just players as sources, the AVR and the TV. I've set the audio to be reproduced on the TV itself. All works fine except Tuner/Radio. There's no sound. Why can't the AVR play radio on my TV?
AVS Forum Addicted Member
Location: Orlando, FL (Scotland until May 22)
Mentioned: 676 Post(s)
Quoted: 21643 Post(s)
Originally Posted by Skylinestar
Currently I don't have any speakers attached to my 3312. Just players as sources, the AVR and the TV. I've set the audio to be reproduced on the TV itself. All works fine except Tuner/Radio. There's no sound. Why can't the AVR play radio on my TV?
Because the setting you changed from 'AVR' to 'TV' is called 'HDMI Audio Out' meaning only HDMI source audio is passed to the TV. 2018 Denon AVR Owner's thread
2018 Marantz AVR Owner's thread
2018 Marantz AVR Owner's thread
Member
Posts: 88
Tagged: 0 Thread(s)
Liked: 4
Static, humming, buzzing noise all vanished after connecting the Boss BN25 between the PC and Denon AVR.
However eventually when I install some new cabinets, pull all the cords, plugs and wiring to determine the actual cause of the noise.
However eventually when I install some new cabinets, pull all the cords, plugs and wiring to determine the actual cause of the noise.
AVS Forum Special Member
Location: Borneo Island
Mentioned: 5 Post(s)
Quoted: 1308 Post(s)
My 3312 was serving perfectly in my home theater setup of Epson projector, Dune media player and Sony bluray player. After upgrading the AVR to a Marantz SR6011 (love the Atmos and XT32), I relocated the 3312 to my living room. The setup is a Samsung plasma tv, a few satellite receivers and a media player, all connected via HDMI. The 3312 acts as a simple switch (previously served by a monoprice HDMI switch) with HDMI audio routed to the tv (no external speakers). What's weird is that my tv will loose signal from the 3312 after approx 5 minutes of usage with any source selected on 3312. I've tried with different HDMI inputs on the tv & swapped with different HDMI cables but to no avail.
What could go wrong?
What could go wrong?
Member
Posts: 88
Tagged: 0 Thread(s)
Liked: 4
Originally Posted by Skylinestar
My 3312 was serving perfectly in my home theater setup of Epson projector, Dune media player and Sony bluray player. After upgrading the AVR to a Marantz SR6011 (love the Atmos and XT32), I relocated the 3312 to my living room. The setup is a Samsung plasma tv, a few satellite receivers and a media player, all connected via HDMI. The 3312 acts as a simple switch (previously served by a monoprice HDMI switch) with HDMI audio routed to the tv (no external speakers). What's weird is that my tv will loose signal from the 3312 after approx 5 minutes of usage with any source selected on 3312. I've tried with different HDMI inputs on the tv & swapped with different HDMI cables but to no avail.
What could go wrong?
I found this thread What could go wrong?
https://www.avsforum.com/forum/90-rec..mi-signal.html
Perform a search such as 'denon avr- 3312 loses hdmi signal'
AVS Forum Addicted Member
Location: Orlando, FL (Scotland until May 22)
Mentioned: 676 Post(s)
Quoted: 21643 Post(s)
Originally Posted by Skylinestar
My 3312 was serving perfectly in my home theater setup of Epson projector, Dune media player and Sony bluray player. After upgrading the AVR to a Marantz SR6011 (love the Atmos and XT32), I relocated the 3312 to my living room. The setup is a Samsung plasma tv, a few satellite receivers and a media player, all connected via HDMI. The 3312 acts as a simple switch (previously served by a monoprice HDMI switch) with HDMI audio routed to the tv (no external speakers). What's weird is that my tv will loose signal from the 3312 after approx 5 minutes of usage with any source selected on 3312. I've tried with different HDMI inputs on the tv & swapped with different HDMI cables but to no avail.
What could go wrong?
Try doing a soft reset (power off and unplug power and HDMI cables for 10 minutes). If still no joy, do a microprocessor reset as noted in post 5 of this thread. What could go wrong?
2018 Denon AVR Owner's thread
2018 Marantz AVR Owner's thread
2018 Marantz AVR Owner's thread
Location: los angeles, california
Mentioned: 1 Post(s)
Quoted: 290 Post(s)
denon 1712
emptek towers and center
i find the treble somewhat lacking. not lively enough for me but dont want a klipsch finger on chalkboard screeching sound
i understand the empteks are a neutral type speaker
but is there any way to up the treble a little like a treble control? i turned dynamic eq off and i think that helped a little, or could just be the placebo effect
also this is wierd. i have a panasonic plasma, i turned viera off but when turning on the avs it defaults to tv unless i turn direct tv and tv on first, then turn the avr on. not sure whats happening there
emptek towers and center
i find the treble somewhat lacking. not lively enough for me but dont want a klipsch finger on chalkboard screeching sound
i understand the empteks are a neutral type speaker
but is there any way to up the treble a little like a treble control? i turned dynamic eq off and i think that helped a little, or could just be the placebo effect
also this is wierd. i have a panasonic plasma, i turned viera off but when turning on the avs it defaults to tv unless i turn direct tv and tv on first, then turn the avr on. not sure whats happening there
| Sponsored Links | |
| ReplyReceivers, Amps, and Processors |
| Tags |
| 4k tv, Denon, Denon Avr 1312 Receiver, Denon Avr 1612 Receiver, Denon Avr 1712 Receiver, Denon Avr 1912 Receiver, Denon Avr 2112ci Receiver, Denon Avr 2312ci Receiver, Denon Avr3312ci Receiver |
«Previous Thread Next Thread
| Posting Rules | |
You may not post replies You may not edit your posts Smilies are On HTML code is Off Pingbacks are Off | |
view our sponsors showcase AVS Forum is proudly sponsored by
For the best viewing experience please update your browser to Google Chrome
We use cookies to improve your experience on this website and so that ads you see online can be tailored to your online browsing interests. We use data about you for a number of purposes explained in the links below. By continuing to browse our site you agree to our use of data and cookies.
Tell me more Cookie Preferences
Tell me more Cookie Preferences
Monster always makes plenty of noise at CES and this year was no different, with 'Head Monster' Noel Lee – resplendent on his gold Segway – revealing tie-ins with Adidas, the UFC, the World Poker Tour, Lamborghini and any number of US music stars.
There was also time to mention Monster's new Pure Monster Sound seal of sound quality approval, a host of new headphones, including the DNA Pro Wireless, and even a return for Monster's 'retro cables', which of course the brand was built upon.
Arguably the company which pioneered the celebrity tie-in, Dr Dre seems a distant memory for Monster, who now have the likes of Nick Cannon, Shaquille O'Neal and UFC fighter Anthony Fettis.
The main new headphones were the DNA Pro Wireless over-ear headphones, which have wireless aptX Bluetooth, active noise-cancellation and 'buttonless touch-sensing control'. There's the option to have a wired connection if you prefer and you can charge the cans via USB.
Available in Q2 2014, the Monster DNA Pro Wireless headphones come with a $450 price tag.
Also new were the Monster Octagon headphones, the new official headphone of the Ultimate Fighting Championship (UFC). UFC is the fastest growing sports organisation of all time, according to Monster, so having cornered a certain corner of the music market, sports seems to be next.
The tie-in with Adidas, which will see Adidas Originals headphones in 2015, is also part of this strategy along with Monster becoming the official headphone supplier for the World Poker Tour – 'the only sport you can play with your headphones on'.
Monster always has an eye on the money no object market, and the Lamborghini relationship is the ultimate example.
The Lamborghini Veneno Roadster, the world's most expensive production car, will now come with a High Performace Audio by Monster in-car sound system. The car costs over £3 million and only nine will be made.
What's more, we hear a rumour that there will also be Monster Lamborghini headphones in the not-too-distant future.
by Joe Cox